Latest firmware on Bambu X1C causing connection issues to Bambu Studio #6110
Comments
|
If you are in LAN-only mode, select Developer Mode on the printer. https://wiki.bambulab.com/en/knowledge-sharing/enable-developer-mode |
|
I'm not in LAN-only mode - it is toggled off
I didn't know there was a developer mode, and would like to turn it on if possible.
…On Mon, Mar 17, 2025 at 10:40 AM LJKraus ***@***.***> wrote:
If you are in LAN-only mode, select Developer mode on the printer.
—
Reply to this email directly, view it on GitHub
<#6110 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/APA3YGKDIQEDCHHQ6AZ2ZFL2U3NGLAVCNFSM6AAAAABZFPJKN6VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDOMRZG43DQNBSG4>
.
You are receiving this because you authored the thread.Message ID:
***@***.***>
[image: LJKraus]*LJKraus* left a comment (bambulab/BambuStudio#6110)
<#6110 (comment)>
If you are in LAN-only mode, select Developer mode on the printer.
—
Reply to this email directly, view it on GitHub
<#6110 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/APA3YGKDIQEDCHHQ6AZ2ZFL2U3NGLAVCNFSM6AAAAABZFPJKN6VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDOMRZG43DQNBSG4>
.
You are receiving this because you authored the thread.Message ID:
***@***.***>
|
|
Sorry, I missed that you are using Studio 1.10.1.50. With the new "authorization" required by X1C firmware 1.08.05, you need to use Studio 1.10.2 or higher to establish a connection via cloud. Developer mode bypasses authorization, but requires LAN-only mode and cannot be used with Bambu cloud services. |
|
Hello, please update to the latest official version V1.10.2.76 on our official website and give it a try. |
|
~Ah yes, so yesterday I checked on github and saw V1.10.2.76 was marked as
*beta*. However, that is not the case if I go to the official Bambu site
to get the latest public release.~
So I actually did install the "~beta~" zip from github yesterday and it
worked - so will be installing the latest exe from the official site today.
Cheers
**<ins>edit: so I must have downloaded the official public release, and not a beta</ins>**
…On Mon, Mar 17, 2025 at 9:45 PM BoBoYu-1 ***@***.***> wrote:
Hello, please update to the latest official version V1.10.2.76 on our
official website and give it a try.
Download Address：https://bambulab.com/zh/download/studio
—
Reply to this email directly, view it on GitHub
<#6110 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/APA3YGOLPDVQKQ2Q64QPRR32U53E3AVCNFSM6AAAAABZFPJKN6VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDOMZRGM3TCOJWHE>
.
You are receiving this because you authored the thread.Message ID:
***@***.***>
[image: BoBoYu-1]*BoBoYu-1* left a comment (bambulab/BambuStudio#6110)
<#6110 (comment)>
Hello, please update to the latest official version V1.10.2.76 on our
official website and give it a try.
Download Address：https://bambulab.com/zh/download/studio
—
Reply to this email directly, view it on GitHub
<#6110 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/APA3YGOLPDVQKQ2Q64QPRR32U53E3AVCNFSM6AAAAABZFPJKN6VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDOMZRGM3TCOJWHE>
.
You are receiving this because you authored the thread.Message ID:
***@***.***>
|
|
V1.10.2.76 became the Public release on Github three weeks ago... |
|
So I downloaded the latest public release zip and thought that it was a beta version... My apologies and thank you for your quick responses 👍 |
|
My apologies, dunno where I was looking... Prob scrolled down past the top
and saw the public beta, sorry abouot that
Message ID: ***@***.***>
… |
Bambu Studio Version
1.10.1.50
Where is the application from?
Bambu Lab Official website
OS version
Windows 11
Additional system information
No response
Printer
X1C
How to reproduce
Update X1C to the latest firmware (01.08.05.00)
Open Bambu Studio and navigate to device page.
Select the updated printer from the My Device list.
Select the Status option, then click on Live View / Camera Feed button.
Or, alternately, select MicroSD Card, then select either Timelapse or Model.
Another thing is to change any of the Nozzle temp, Bed temp, Fan speed, Home, etc settings
Actual results
from step 4. I get the following error:
Connection Failed. Please check the network and try again [1:3]
from step 5. I catch the same issue and have no access to either the Timelapse or MicroSD Card
from step 6. None of the changes made under the control tab take effect (heat, fan, speed, home, etc)
Error in HMS:
(MQTT command verification failed, please update the Studio or Handy)
Expected results
from step 4. The liveview on the camera turns on, showing the print bed
from step 5. The contents of the MicroSD Card show up, as well as the Timelapse videos
from step 6. I am able to adjust temperatures, speed, home etc., from under the control tab
Project file & Debug log uploads
Untitled.zip
Checklist of files to include
The text was updated successfully, but these errors were encountered: