spi.cpp

#ifndef KERNEL_MODULE
#include <stdio.h> // printf, stderr
#include <syslog.h> // syslog
#include <fcntl.h> // open, O_RDWR, O_SYNC
#include <sys/mman.h> // mmap, munmap
#include <pthread.h> // pthread_create
#include <bcm_host.h> // bcm_host_get_peripheral_address, bcm_host_get_peripheral_size, bcm_host_get_sdram_address
#include "config.h"
#endif

#include "config.h"
#include "spi_user.h"
#include "util.h"
#include "dma.h"
#include "mailbox.h"
#include "mem_alloc.h"

// Uncomment this to print out all bytes sent to the SPI bus
// #define DEBUG_SPI_BUS_WRITES

#ifdef DEBUG_SPI_BUS_WRITES
#define DEBUG_PRINT_WRITTEN_BYTE(byte) do { \
  printf("%02X", byte); \
  if ((writeCounter & 3) == 0) printf("\n"); \
  } while(0)
#else
#define DEBUG_PRINT_WRITTEN_BYTE(byte) ((void)0)
#endif

#ifdef CHIP_SELECT_LINE_NEEDS_REFRESHING_EACH_32BITS_WRITTEN
void ChipSelectHigh();
#define TOGGLE_CHIP_SELECT_LINE() if ((++writeCounter & 3) == 0) { ChipSelectHigh(); }
#else
#define TOGGLE_CHIP_SELECT_LINE() ((void)0)
#endif

static uint32_t writeCounter = 0;

#define WRITE_FIFO(word) do { \
  uint8_t w = (word); \
  spi->fifo = w; \
  TOGGLE_CHIP_SELECT_LINE(); \
  DEBUG_PRINT_WRITTEN_BYTE(w); \
  } while(0)

int mem_fd = -1;
int intr_fd = -1;
static int numberPress = 0;
static char numberAsString[21] = "                    ";
volatile void *bcm2835 = 0;
volatile GPIORegisterFile *gpio = 0;
volatile SPIRegisterFile *spi = 0;

// Points to the system timer register. N.B. spec sheet says this is two low and high parts, in an 32-bit aligned (but not 64-bit aligned) address. Profiling shows
// that Pi 3 Model B does allow reading this as a u64 load, and even when unaligned, it is around 30% faster to do so compared to loading in parts "lo | (hi << 32)".
volatile uint64_t *systemTimerRegister = 0;

bool hasInterrupt() {
    int lastNumberPress = numberPress;
    
    if(intr_fd<0) return false;
    if ((read(intr_fd, numberAsString, sizeof(numberAsString))) < 0) {
        if (errno != EWOULDBLOCK) {
            perror("read/intr_fd");
        }
    } else {
    	lseek(intr_fd,0,SEEK_SET);
        numberPress = atoi(numberAsString);
    }
    return (numberPress != lastNumberPress);
}

void DumpSPICS(uint32_t reg)
{
  PRINT_FLAG(BCM2835_SPI0_CS_CS);
  PRINT_FLAG(BCM2835_SPI0_CS_CPHA);
  PRINT_FLAG(BCM2835_SPI0_CS_CPOL);
  PRINT_FLAG(BCM2835_SPI0_CS_CLEAR_TX);
  PRINT_FLAG(BCM2835_SPI0_CS_CLEAR_RX);
  PRINT_FLAG(BCM2835_SPI0_CS_TA);
  PRINT_FLAG(BCM2835_SPI0_CS_DMAEN);
  PRINT_FLAG(BCM2835_SPI0_CS_INTD);
  PRINT_FLAG(BCM2835_SPI0_CS_INTR);
  PRINT_FLAG(BCM2835_SPI0_CS_ADCS);
  PRINT_FLAG(BCM2835_SPI0_CS_DONE);
  PRINT_FLAG(BCM2835_SPI0_CS_RXD);
  PRINT_FLAG(BCM2835_SPI0_CS_TXD);
  PRINT_FLAG(BCM2835_SPI0_CS_RXR);
  PRINT_FLAG(BCM2835_SPI0_CS_RXF);
  printf("SPI0 DLEN: %u\n", spi->dlen);
  printf("SPI0 CE0 register: %d\n", GET_GPIO(GPIO_SPI0_CE0) ? 1 : 0);
}

#ifdef RUN_WITH_REALTIME_THREAD_PRIORITY

#include <pthread.h>
#include <sched.h>

void SetRealtimeThreadPriority()
{
  sched_param params;
  params.sched_priority = sched_get_priority_max(SCHED_FIFO);

  int failed = pthread_setschedparam(pthread_self(), SCHED_FIFO, &params);
  if (failed) FATAL_ERROR("pthread_setschedparam() failed!");

  int policy = 0;
  failed = pthread_getschedparam(pthread_self(), &policy, &params);
  if (failed) FATAL_ERROR("pthread_getschedparam() failed!");

  if (policy != SCHED_FIFO) FATAL_ERROR("Failed to set realtime thread policy!");
  printf("Set fbcp-ili9341 thread scheduling priority to maximum (%d)\n", sched_get_priority_max(SCHED_FIFO));
}

#endif

// Errata to BCM2835 behavior: documentation states that the SPI0 DLEN register is only used for DMA. However, even when DMA is not being utilized, setting it from
// a value != 0 or 1 gets rid of an excess idle clock cycle that is present when transmitting each byte. (by default in Polled SPI Mode each 8 bits transfer in 9 clocks)
// With DLEN=2 each byte is clocked to the bus in 8 cycles, observed to improve max throughput from 56.8mbps to 63.3mbps (+11.4%, quite close to the theoretical +12.5%)
// https://www.raspberrypi.org/forums/viewtopic.php?f=44&t=181154
#define UNLOCK_FAST_8_CLOCKS_SPI() (spi->dlen = 2)

#ifdef ALL_TASKS_SHOULD_DMA
bool previousTaskWasSPI = true;
#endif

#ifdef SPI_3WIRE_PROTOCOL

uint32_t NumBytesNeededFor32BitSPITask(uint32_t byteSizeFor8BitTask)
{
  return byteSizeFor8BitTask * 2 + 4; // 16bit -> 32bit expansion, plus 4 bytes for command word
}

uint32_t NumBytesNeededFor9BitSPITask(uint32_t byteSizeFor8BitTask)
{
  uint32_t numOutBits = (byteSizeFor8BitTask + 1) * 9;
  // The number of bits we send out in a command must be a multiple of 9 bits, because each byte is 1 data/command bit plus 8 payload bits
  // But the number of bits sent out in a command must also be a multiple of 8 bits, because BCM2835 SPI peripheral only deals with sending out full bytes.
  // Therefore the bits written out must be a multiple of lcm(9*8)=72bits.
  numOutBits = ((numOutBits + 71) / 72) * 72;
  uint32_t numOutBytes = numOutBits >> 3;
  return numOutBytes;
}

// N.B. BCM2835 hardware always clocks bytes out most significant bit (MSB) first, so when interleaving, the command bit needs to start out in the
// highest byte of the outgoing buffer.
void Interleave8BitSPITaskTo9Bit(SPITask *task)
{
  const uint32_t size8BitTask = task->size - task->sizeExpandedTaskWithPadding;

  // 9-bit SPI task lives right at the end of the 8-bit task
  uint8_t *dst = task->data + size8BitTask;

  // Pre-clear the 9*8=72 bit tail end of the memory to all zeroes to avoid having to pad source data to multiples of 9. (plus padding bytes, just to be safe)
  memset(dst + task->sizeExpandedTaskWithPadding - 9 - SPI_9BIT_TASK_PADDING_BYTES, 0, 9 + SPI_9BIT_TASK_PADDING_BYTES);

  // Fill first command byte xxxxxxxx -> 0xxxxxxx x: (low 0 bit to indicate a command byte)
  dst[0] = task->cmd >> 1;
  dst[1] = task->cmd << 7;
  int dstByte = 1;
  int dstBitsUsed = 1;

  int src = 0;

  // Command bit above produced one byte. If there are at least 7 bytes in the data set, we can complete a set of 8 transferred bytes. Fast track
  // that:
  if (size8BitTask >= 7)
  {
    dst[1] |= 0x40 |                        (task->data[0] >> 2);
    dst[2]  = 0x20 | (task->data[0] << 6) | (task->data[1] >> 3);
    dst[3]  = 0x10 | (task->data[1] << 5) | (task->data[2] >> 4);
    dst[4]  = 0x08 | (task->data[2] << 4) | (task->data[3] >> 5);
    dst[5]  = 0x04 | (task->data[3] << 3) | (task->data[4] >> 6);
    dst[6]  = 0x02 | (task->data[4] << 2) | (task->data[5] >> 7);
    dst[7]  = 0x01 | (task->data[5] << 1);
    dst[8]  =        (task->data[6]     );
    dstByte = 9;
    dstBitsUsed = 0;
    src = 7;

    // More fast tracking: As long as we have multiples of 8 bytes left, fast fill them in
    while(src <= size8BitTask - 8)
    {
      uint8_t *d = dst + dstByte;
      dstByte += 9;
      const uint8_t *s = task->data + src;
      src += 8;

      d[0] = 0x80 |               (s[0] >> 1);
      d[1] = 0x40 | (s[0] << 7) | (s[1] >> 2);
      d[2] = 0x20 | (s[1] << 6) | (s[2] >> 3);
      d[3] = 0x10 | (s[2] << 5) | (s[3] >> 4);
      d[4] = 0x08 | (s[3] << 4) | (s[4] >> 5);
      d[5] = 0x04 | (s[4] << 3) | (s[5] >> 6);
      d[6] = 0x02 | (s[5] << 2) | (s[6] >> 7);
      d[7] = 0x01 | (s[6] << 1);
      d[8] = (s[7]     );
    }

    // Pre-clear the next byte to be written - the slow loop below assumes it is continuing a middle of byte sequence
    // N.B. This write could happen to memory that is not part of the task, so memory allocation of the 9-bit task needs to allocate one byte of padding
    dst[dstByte] = 0;
  }

  // Fill tail data bytes, slow path
  while(src < size8BitTask)
  {
    uint8_t data = task->data[src++];

    // High 1 bit to indicate a data byte
    dst[dstByte] |= 1 << (7 - dstBitsUsed);
    ++dstBitsUsed;
    if (dstBitsUsed == 8) // Written data bit completes a full byte?
    {
      ++dstByte; // Advance to next byte
      dstBitsUsed = 0;
      // Now we are aligned, so can write the data byte directly
      dst[dstByte++] = data;
      dst[dstByte] = 0; // Clear old contents of the next byte to write
    }
    else
    {
      // 8 data bits
      dst[dstByte++] |= data >> dstBitsUsed;
      // This is the first write to the next byte, that should occur without ORring to clear old data in memory
      // N.B. This write could happen to memory that is not part of the task, so memory allocation of the 9-bit task needs to allocate one byte of padding
      dst[dstByte] = data << (8 - dstBitsUsed);
    }
  }

#if 0 // Enable to debug correctness:

#define BYTE_TO_BINARY_PATTERN "%c%c%c%c%c%c%c%c"
#define BYTE_TO_BINARY(byte)  \
  (byte & 0x80 ? '1' : '0'), \
  (byte & 0x40 ? '1' : '0'), \
  (byte & 0x20 ? '1' : '0'), \
  (byte & 0x10 ? '1' : '0'), \
  (byte & 0x08 ? '1' : '0'), \
  (byte & 0x04 ? '1' : '0'), \
  (byte & 0x02 ? '1' : '0'), \
  (byte & 0x01 ? '1' : '0')

  printf("Interleaving result: 8-bit task of size %d bytes became %d bytes:\n", task->size - task->sizeExpandedTaskWithPadding, task->sizeExpandedTaskWithPadding - SPI_9BIT_TASK_PADDING_BYTES);
  printf("8-bit c" BYTE_TO_BINARY_PATTERN, BYTE_TO_BINARY(task->cmd));
  for(int i = 0; i < task->size - task->sizeExpandedTaskWithPadding; ++i)
    printf("d" BYTE_TO_BINARY_PATTERN, BYTE_TO_BINARY(task->data[i]));
  printf("\n9-bit ");
  for(int i = 0; i < task->sizeExpandedTaskWithPadding - SPI_9BIT_TASK_PADDING_BYTES; ++i)
    printf(BYTE_TO_BINARY_PATTERN, BYTE_TO_BINARY(dst[i]));
  printf("\n\n");
#endif

}

void Interleave16BitSPITaskTo32Bit(SPITask *task)
{
  const uint32_t size8BitTask = task->size - task->sizeExpandedTaskWithPadding;

  // 32-bit SPI task lives right at the end of the 16-bit task
  uint32_t *dst = (uint32_t *)(task->data + size8BitTask);
  *dst++ = task->cmd;

  const uint32_t taskSizeU16 = size8BitTask >> 1;
  uint16_t *src = (uint16_t*)task->data;
  for(uint32_t i = 0; i < taskSizeU16; ++i)
    dst[i] = 0x1500 | (src[i] << 16);
}

#endif // ~SPI_3WIRE_PROTOCOL

void WaitForPolledSPITransferToFinish()
{
  uint32_t cs;
  while (!(((cs = spi->cs) ^ BCM2835_SPI0_CS_TA) & (BCM2835_SPI0_CS_DONE | BCM2835_SPI0_CS_TA))) // While TA=1 and DONE=0
    if ((cs & (BCM2835_SPI0_CS_RXR | BCM2835_SPI0_CS_RXF)))
      spi->cs = BCM2835_SPI0_CS_CLEAR_RX | BCM2835_SPI0_CS_TA | DISPLAY_SPI_DRIVE_SETTINGS;

  if ((cs & BCM2835_SPI0_CS_RXD)) spi->cs = BCM2835_SPI0_CS_CLEAR_RX | BCM2835_SPI0_CS_TA | DISPLAY_SPI_DRIVE_SETTINGS;
}

void sendNoOpCommand() {
  // Send a no-operation command to display (side effect is Touch display is polled)
  SPITask *task = AllocTask(0);
  task->cmd = DISPLAY_NO_OPERATION;
  CommitTask(task);
  IN_SINGLE_THREADED_MODE_RUN_TASK();
}

#ifdef ALL_TASKS_SHOULD_DMA

#ifndef USE_DMA_TRANSFERS
#error When building with #define ALL_TASKS_SHOULD_DMA enabled, -DUSE_DMA_TRANSFERS=ON should be set in CMake command line!
#endif

// Synchonously performs a single SPI command byte + N data bytes transfer on the calling thread. Call in between a BEGIN_SPI_COMMUNICATION() and END_SPI_COMMUNICATION() pair.
void RunSPITask(SPITask *task)
{
  uint32_t cs;
  uint8_t *tStart = task->PayloadStart();
  uint8_t *tEnd = task->PayloadEnd();
  const uint32_t payloadSize = tEnd - tStart;
  uint8_t *tPrefillEnd = tStart + MIN(15, payloadSize);
#define TASK_SIZE_TO_USE_DMA 4
  // Do a DMA transfer if this task is suitable in size for DMA to handle
  if (payloadSize >= TASK_SIZE_TO_USE_DMA && (task->cmd == DISPLAY_WRITE_PIXELS || task->cmd == DISPLAY_SET_CURSOR_X || task->cmd == DISPLAY_SET_CURSOR_Y))
  {
    if (previousTaskWasSPI)
      WaitForPolledSPITransferToFinish();
    //printf("DMA cmd=0x%x, data=%d bytes\n", task->cmd, task->PayloadSize());
    SPIDMATransfer(task);
    previousTaskWasSPI = false;
  }
  else
  {
    if (!previousTaskWasSPI)
    {
      WaitForDMAFinished();
      spi->cs = BCM2835_SPI0_CS_TA | BCM2835_SPI0_CS_CLEAR_TX | DISPLAY_SPI_DRIVE_SETTINGS;
      // After having done a DMA transfer, the SPI0 DLEN register has reset to zero, so restore it to fast mode.
      UNLOCK_FAST_8_CLOCKS_SPI();
    }
    else
      WaitForPolledSPITransferToFinish();

    //printf("SPI cmd=0x%x, data=%d bytes\n", task->cmd, task->PayloadSize());

  // Send the command word if display is 4-wire (3-wire displays can omit this, commands are interleaved in the data payload stream above)
#ifndef SPI_3WIRE_PROTOCOL
    CLEAR_GPIO(GPIO_TFT_DATA_CONTROL);

#ifdef DISPLAY_SPI_BUS_IS_16BITS_WIDE
    // On e.g. the ILI9486, all commands are 16-bit, so need to be clocked in in two bytes. The MSB byte is always zero though in all the defined commands.
    WRITE_FIFO(0x00);
#endif
    WRITE_FIFO(task->cmd);

#ifdef DISPLAY_SPI_BUS_IS_16BITS_WIDE
    while(!(spi->cs & (BCM2835_SPI0_CS_DONE))) /*nop*/;
    spi->fifo;
    spi->fifo;
#else
    while(!(spi->cs & (BCM2835_SPI0_CS_RXD|BCM2835_SPI0_CS_DONE))) /*nop*/;
#endif

    SET_GPIO(GPIO_TFT_DATA_CONTROL);
#endif

    // Send the data payload:
    while(tStart < tPrefillEnd) WRITE_FIFO(*tStart++);
    while(tStart < tEnd)
    {
      cs = spi->cs;
      if ((cs & BCM2835_SPI0_CS_TXD)) WRITE_FIFO(*tStart++);
// TODO:      else asm volatile("yield");
      if ((cs & (BCM2835_SPI0_CS_RXR|BCM2835_SPI0_CS_RXF))) spi->cs = BCM2835_SPI0_CS_CLEAR_RX | BCM2835_SPI0_CS_TA | DISPLAY_SPI_DRIVE_SETTINGS;
    }

    previousTaskWasSPI = true;
  }
}
#else

void RunSPITask(SPITask *task)
{
  WaitForPolledSPITransferToFinish();

  // The Adafruit 1.65" 240x240 ST7789 based display is unique compared to others that it does want to see the Chip Select line go
  // low and high to start a new command. For that display we let hardware SPI toggle the CS line, and actually run TA<-0 and TA<-1
  // transitions to let the CS line live. For most other displays, we just set CS line always enabled for the display throughout fbcp-ili9341 lifetime,
  // which is a tiny bit faster.
#ifdef DISPLAY_NEEDS_CHIP_SELECT_SIGNAL
  BEGIN_SPI_COMMUNICATION();
#endif

  uint8_t *tStart = task->PayloadStart();
  uint8_t *tEnd = task->PayloadEnd();
  const uint32_t payloadSize = tEnd - tStart;
  uint8_t *tPrefillEnd = tStart + MIN(15, payloadSize);

  // Send the command word if display is 4-wire (3-wire displays can omit this, commands are interleaved in the data payload stream above)
#ifndef SPI_3WIRE_PROTOCOL
  // An SPI transfer to the display always starts with one control (command) byte, followed by N data bytes.
  CLEAR_GPIO(GPIO_TFT_DATA_CONTROL);

#ifdef DISPLAY_SPI_BUS_IS_16BITS_WIDE
  // On e.g. the ILI9486, all commands are 16-bit, so need to be clocked in in two bytes. The MSB byte is always zero though in all the defined commands.
  WRITE_FIFO(0x00);
#endif
  WRITE_FIFO(task->cmd);

#ifdef DISPLAY_SPI_BUS_IS_16BITS_WIDE
  while(!(spi->cs & (BCM2835_SPI0_CS_DONE))) /*nop*/;
  spi->fifo;
  spi->fifo;
#else
  while(!(spi->cs & (BCM2835_SPI0_CS_RXD|BCM2835_SPI0_CS_DONE))) /*nop*/;
#endif

  SET_GPIO(GPIO_TFT_DATA_CONTROL);
#endif // ~!SPI_3WIRE_PROTOCOL

// For small transfers, using DMA is not worth it, but pushing through with polled SPI gives better bandwidth.
// For larger transfers though that are more than this amount of bytes, using DMA is faster.
// This cutoff number was experimentally tested to find where Polled SPI and DMA are as fast.
#define DMA_IS_FASTER_THAN_POLLED_SPI 140
  // Do a DMA transfer if this task is suitable in size for DMA to handle
#ifdef USE_DMA_TRANSFERS
  if (tEnd - tStart > DMA_IS_FASTER_THAN_POLLED_SPI)
  {
    SPIDMATransfer(task);

    // After having done a DMA transfer, the SPI0 DLEN register has reset to zero, so restore it to fast mode.
    UNLOCK_FAST_8_CLOCKS_SPI();
  }
  else
#endif
  {
    while(tStart < tPrefillEnd) WRITE_FIFO(*tStart++);
    while(tStart < tEnd)
    {
      uint32_t cs = spi->cs;
      if ((cs & BCM2835_SPI0_CS_TXD)) WRITE_FIFO(*tStart++);
// TODO:      else asm volatile("yield");
      if ((cs & (BCM2835_SPI0_CS_RXR|BCM2835_SPI0_CS_RXF))) spi->cs = BCM2835_SPI0_CS_CLEAR_RX | BCM2835_SPI0_CS_TA | DISPLAY_SPI_DRIVE_SETTINGS;
    }
  }

#ifdef DISPLAY_NEEDS_CHIP_SELECT_SIGNAL
  END_SPI_COMMUNICATION();
#endif
}
#endif

SharedMemory *spiTaskMemory = 0;
volatile uint64_t spiThreadIdleUsecs = 0;
volatile uint64_t spiThreadSleepStartTime = 0;
volatile int spiThreadSleeping = 0;
double spiUsecsPerByte;

SPITask *GetTask() // Returns the first task in the queue, called in worker thread
{
  uint32_t head = spiTaskMemory->queueHead;
  uint32_t tail = spiTaskMemory->queueTail;
  if (head == tail) return 0;
  SPITask *task = (SPITask*)(spiTaskMemory->buffer + head);
  if (task->cmd == 0) // Wrapped around?
  {
    spiTaskMemory->queueHead = 0;
    __sync_synchronize();
    if (tail == 0) return 0;
    task = (SPITask*)spiTaskMemory->buffer;
  }
  return task;
}

void DoneTask(SPITask *task) // Frees the first SPI task from the queue, called in worker thread
{
  __atomic_fetch_sub(&spiTaskMemory->spiBytesQueued, task->PayloadSize()+1, __ATOMIC_RELAXED);
  spiTaskMemory->queueHead = (uint32_t)((uint8_t*)task - spiTaskMemory->buffer) + sizeof(SPITask) + task->size;
  __sync_synchronize();
}

extern volatile bool programRunning;

void ExecuteSPITasks()
{
#ifndef USE_DMA_TRANSFERS
  BEGIN_SPI_COMMUNICATION();
#endif
  {
    while(programRunning && spiTaskMemory->queueTail != spiTaskMemory->queueHead)
    {
      SPITask *task = GetTask();
      if (task)
      {
        RunSPITask(task);
        DoneTask(task);
      }
    }
  }
#ifndef USE_DMA_TRANSFERS
  END_SPI_COMMUNICATION();
#endif
}

#if defined(USE_SPI_THREAD)
pthread_t spiThread;

// A worker thread that keeps the SPI bus filled at all times
void *spi_thread(void *unused)
{
#ifdef RUN_WITH_REALTIME_THREAD_PRIORITY
  SetRealtimeThreadPriority();
#endif
  while(programRunning)
  {
    if (spiTaskMemory->queueTail != spiTaskMemory->queueHead)
    {
      ExecuteSPITasks();
    }
    else
    {
#ifdef STATISTICS
      uint64_t t0 = tick();
      spiThreadSleepStartTime = t0;
      __atomic_store_n(&spiThreadSleeping, 1, __ATOMIC_RELAXED);
#endif
      if (programRunning) {
	syscall(SYS_futex, &spiTaskMemory->queueTail, FUTEX_WAIT, spiTaskMemory->queueHead, 0, 0, 0); // Start sleeping until we get new tasks
      }
#ifdef STATISTICS
      __atomic_store_n(&spiThreadSleeping, 0, __ATOMIC_RELAXED);
      uint64_t t1 = tick();
      __sync_fetch_and_add(&spiThreadIdleUsecs, t1-t0);
#endif
    }
  }
  pthread_exit(0);
}
#endif



int InitSPI()
{
  // Memory map GPIO and SPI peripherals for direct access
  mem_fd = open("/dev/mem", O_RDWR|O_SYNC);
  if (mem_fd < 0) FATAL_ERROR("can't open /dev/mem (run as sudo)");
  printf("bcm_host_get_peripheral_address: %p, bcm_host_get_peripheral_size: %u, bcm_host_get_sdram_address: %p\n", bcm_host_get_peripheral_address(), bcm_host_get_peripheral_size(), bcm_host_get_sdram_address());
  bcm2835 = mmap(NULL, bcm_host_get_peripheral_size(), (PROT_READ | PROT_WRITE), MAP_SHARED, mem_fd, bcm_host_get_peripheral_address());
  if (bcm2835 == MAP_FAILED) FATAL_ERROR("mapping /dev/mem failed");
  spi = (volatile SPIRegisterFile*)((uintptr_t)bcm2835 + BCM2835_SPI0_BASE);
  gpio = (volatile GPIORegisterFile*)((uintptr_t)bcm2835 + BCM2835_GPIO_BASE);
  systemTimerRegister = (volatile uint64_t*)((uintptr_t)bcm2835 + BCM2835_TIMER_BASE + 0x04); // Generates an unaligned 64-bit pointer, but seems to be fine.
  // TODO: On graceful shutdown, (ctrl-c signal?) close(mem_fd)

  // Touch screen interrupt
  intr_fd = open("/sys/tft/gpio25/numberPresses", O_RDONLY|O_NONBLOCK);
  //if (intr_fd < 0) FATAL_ERROR("can't open /sys/tft/gpio25/numberPresses (run as sudo)");
    
  uint32_t currentBcmCoreSpeed = MailboxRet2(0x00030002/*Get Clock Rate*/, 0x4/*CORE*/);
  uint32_t maxBcmCoreTurboSpeed = MailboxRet2(0x00030004/*Get Max Clock Rate*/, 0x4/*CORE*/);

  // Estimate how many microseconds transferring a single byte over the SPI bus takes?
  spiUsecsPerByte = 1000000.0 * 8.0/*bits/byte*/ * SPI_BUS_CLOCK_DIVISOR / maxBcmCoreTurboSpeed;

  printf("BCM core speed: current: %uhz, max turbo: %uhz. SPI CDIV: %d, SPI max frequency: %.0fhz\n", currentBcmCoreSpeed, maxBcmCoreTurboSpeed, SPI_BUS_CLOCK_DIVISOR, (double)maxBcmCoreTurboSpeed / SPI_BUS_CLOCK_DIVISOR);

  // By default all GPIO pins are in input mode (0x00), initialize them for SPI and GPIO writes
#ifdef GPIO_TFT_DATA_CONTROL
  SET_GPIO_MODE(GPIO_TFT_DATA_CONTROL, 0x01); // Data/Control pin to output (0x01)
#endif
  SET_GPIO_MODE(GPIO_SPI0_MISO, 0x04);
  SET_GPIO_MODE(GPIO_SPI0_MOSI, 0x04);
  SET_GPIO_MODE(GPIO_SPI0_CLK, 0x04);

#ifdef DISPLAY_NEEDS_CHIP_SELECT_SIGNAL
  // The Adafruit 1.65" 240x240 ST7789 based display is unique compared to others that it does want to see the Chip Select line go
  // low and high to start a new command. For that display we let hardware SPI toggle the CS line, and actually run TA<-0 and TA<-1
  // transitions to let the CS line live. For most other displays, we just set CS line always enabled for the display throughout
  // fbcp-ili9341 lifetime, which is a tiny bit faster.
  SET_GPIO_MODE(GPIO_SPI0_CE0, 0x04);
#ifdef DISPLAY_USES_CS1
  SET_GPIO_MODE(GPIO_SPI0_CE1, 0x04);
#endif
#else
  // Set the SPI 0 pin explicitly to output, and enable chip select on the line by setting it to low.
  // fbcp-ili9341 assumes exclusive access to the SPI0 bus, and exclusive presence of only one device on the bus,
  // which is (permanently) activated here.
  SET_GPIO_MODE(GPIO_SPI0_CE0, 0x01);
  CLEAR_GPIO(GPIO_SPI0_CE0);
#ifdef DISPLAY_USES_CS1
  SET_GPIO_MODE(GPIO_SPI0_CE1, 0x01);
#endif
#endif

  spi->cs = BCM2835_SPI0_CS_CLEAR | DISPLAY_SPI_DRIVE_SETTINGS; // Initialize the Control and Status register to defaults: CS=0 (Chip Select), CPHA=0 (Clock Phase), CPOL=0 (Clock Polarity), CSPOL=0 (Chip Select Polarity), TA=0 (Transfer not active), and reset TX and RX queues.
  spi->clk = SPI_BUS_CLOCK_DIVISOR; // Clock Divider determines SPI bus speed, resulting speed=256MHz/clk

  spiTaskMemory = (SharedMemory*)Malloc(SHARED_MEMORY_SIZE, "spi.cpp shared task memory");
  spiTaskMemory->queueHead = spiTaskMemory->queueTail = spiTaskMemory->spiBytesQueued = 0;

#ifdef USE_DMA_TRANSFERS
  InitDMA();
#endif

  // Enable fast 8 clocks per byte transfer mode, instead of slower 9 clocks per byte.
  UNLOCK_FAST_8_CLOCKS_SPI();

  printf("Initializing display\n");
  InitSPIDisplay();

#ifdef USE_SPI_THREAD
  // Create a dedicated thread to feed the SPI bus. While this is fast, it consumes a lot of CPU. It would be best to replace
  // this thread with a kernel module that processes the created SPI task queue using interrupts. (while juggling the GPIO D/C line as well)
  printf("Creating SPI task thread\n");
  int rc = pthread_create(&spiThread, NULL, spi_thread, NULL); // After creating the thread, it is assumed to have ownership of the SPI bus, so no SPI chat on the main thread after this.
  if (rc != 0) FATAL_ERROR("Failed to create SPI thread!");
#else
  // We will be running SPI tasks continuously from the main thread, so keep SPI Transfer Active throughout the lifetime of the driver.
  BEGIN_SPI_COMMUNICATION();
#endif
  LOG("InitSPI done");
  return 0;
}

void DeinitSPI()
{
#ifdef USE_SPI_THREAD
  pthread_join(spiThread, NULL);
  spiThread = (pthread_t)0;
#endif
  DeinitSPIDisplay();
#ifdef USE_DMA_TRANSFERS
  DeinitDMA();
#endif

  spi->cs = BCM2835_SPI0_CS_CLEAR | DISPLAY_SPI_DRIVE_SETTINGS;

#ifdef GPIO_TFT_DATA_CONTROL
  SET_GPIO_MODE(GPIO_TFT_DATA_CONTROL, 0);
#endif
  SET_GPIO_MODE(GPIO_SPI0_CE1, 0);
  SET_GPIO_MODE(GPIO_SPI0_CE0, 0);
  SET_GPIO_MODE(GPIO_SPI0_MISO, 0);
  SET_GPIO_MODE(GPIO_SPI0_MOSI, 0);
  SET_GPIO_MODE(GPIO_SPI0_CLK, 0);

  if (bcm2835)
  {
    munmap((void*)bcm2835, bcm_host_get_peripheral_size());
    bcm2835 = 0;
  }

  if (mem_fd >= 0)
  {
    close(mem_fd);
    mem_fd = -1;
  }
  if (intr_fd >= 0) {
    close(intr_fd);
    intr_fd = -1;
  }
  free(spiTaskMemory);
  spiTaskMemory = 0;
}