docs/m2k: Fix to match current sections for M2kPlugin

Signed-off-by: Andrei-Fabian-Pop <[email protected]>

docs/tests/plugins/m2k/general_settings_tests.rst

@@ -232,27 +232,26 @@ Test 3: Preferences
 
 **UID:** TST.GEN.SETUP.PREFERENCES
 
-**Description:** This test verifies the preferences feature of Scopy. It checks the seven sections of the preferences menu and the options available in each section.
+**Description:** This test verifies the preferences feature of Scopy. It checks the sections of the preferences menu and the options available in each section.
 
 **Preconditions:**
         - Scopy is installed on the system.
         - OS: ANY
         - Use :ref:`M2k.Usb <m2k-usb-general-settings>` setup.
 
 **Steps:**
-        1. Click the Preferences option located below the instrument options.
-                - **Expected Result:** The Preferences menu should contain seven sections: General, Oscilloscope, Spectrum Analyzer, Logic Analyzer, Signal Generator, Network Analyzer, and Debug.
+        1. Click the Preferences option located below the instrument options. After the Preferences menu appears, click the M2kPlugin tab.
+                - **Expected Result:** The Preferences menu should contain several sections: General, Analog tools and Logic tools.
                 - **Actual Result:**
 
 ..
   Actual test result goes here.
 ..
 
-        2. Enable “Save session when closing Scopy.”
+        2. Enable “Save session when closing Scopy.” (This is in the General tab)
         3. Use Scopy and play with its instruments, changing the configurations and settings. Close Scopy and reopen.
-        4. Enable “Show advanced device information.”
-        5. On the Home menu, click the M2K icon and drag down to see the advanced device information.
-                - **Expected Result:** A dialog box should appear confirming the reset command.
+        5. On the General tab, click the M2K icon and drag down to see the debug section.
+                - **Expected Result:** A dialog box with the "Restart" text should appear confirming the reset command. 
                 - **Actual Result:**
 
 ..
@@ -268,15 +267,15 @@ Test 3: Preferences
   Actual test result goes here.
 ..
 
-        8. Under the Oscilloscope section, labels on the plot may be toggled on or off.
+        8. In the M2kPlugin Tab, under the Analog tools section, labels on the plot may be toggled on or off.
                 - **Expected Result:** Checking the Oscilloscope plot, the labels must synchronize with the option chosen.
                 - **Actual Result:**
 
 ..
   Actual test result goes here.
 ..
 
-        9. On the Spectrum Analyzer section, an option to search or not to search marker peaks in the visible domain is given.
+        9. On the Analog tools section, an option to search or not to search marker peaks in the visible domain is given.
         10. Signal Generator’s Settings: For Channel 1: Sinewave, 10Vpp, 500kHz. Spectrum Analyzer’s Sweep Settings: Start – 700kHz, Stop – 1MHz. Disable Channel 2. Connect AWG channel 1 to Scope Ch1+.
         11. Under the Marker Settings, click Marker 1 then “Peak.” Turn the Marker Table on and look for the marked frequencies.
                  - **Expected Result:** A marker labeled M1 will automatically appear on the spectrum upon clicking Marker 1. Clicking “Peak” will put the Marker on the 500kHz mark.
@@ -286,15 +285,15 @@ Test 3: Preferences
   Actual test result goes here.
 ..
 
-        12. Under the Signal Generator section, The number of periods shown may be adjusted from 2 to 9.
+        12. Under the Analog tools section, The number of periods shown may be adjusted from 2 to 9.
                  - **Expected Result:** The signal generator’s graphical representation must follow the desired number of periods on the lower frequency channel (if both channels are configured to output waveform signals). When numbers other than 2 to 9 are entered, the number and the line under it turns to red.
                  - **Actual Result:**
 
 ..
   Actual test result goes here.
 ..
 
-        13. On the Network Analyzer section, an option to display 0dB on the graph is available. Click to enable it.
+        13. On the Analog tools section, an option to display 0dB on the graph is available. Click to enable it.
         14. Construct a first-order low pass RC filter with the following components: R = 470 Ohms, C = 1uF. This will have a cut-off frequency of ~340 Hz.
         15. Network Analyzer’s Settings: Reference: Channel 1, 1V Amplitude, 0V Offset. Sweep: Logarithmic, Start – 10Hz, Stop – 500kHz, Sample Count - 100. Display: Min. Magnitude – -90dB, Max. Magnitude – 10dB, Min. Phase – -150deg, Max. Phase – 60deg. Run Network Analyzer.
                  - **Expected Result:** The Bode Plot has 0dB on its labels.