docs/tests: add test report structure to the M2K plugin tests.

Signed-off-by: AlexandraTrifan <[email protected]>

docs/tests/plugins/m2k/digital_io_tests.rst

@@ -13,6 +13,23 @@ Digital IO instrument of the ADALM2000 plugin in Scopy.
 The following apply for all the test cases in this suite.
 If the test case has special requirements, they will be listed in the test case section.
 
+
+.. note::
+    .. list-table:: 
+       :widths: 50 30 30 50 50
+       :header-rows: 1
+
+       * - Tester
+         - Test Date
+         - Scopy version
+         - Plugin version (N/A if not applicable)
+         - Comments
+       * - 
+         - 
+         - 
+         - 
+         - 
+
 Setup environment:
 ------------------
 
@@ -56,30 +73,80 @@ Test 1 - Check individual digital pin state
               (the corresponding led will be turned on).
             - When DIO 0 is set to logic 0, DIO 7 will be automatically set to logic 0
               (the corresponding led will be turned off).
+
+        - **Actual Result**:
+
+..
+  Actual test result goes here.
+..
+
     6. Connect DIO 0 to a the analog pin **1+** and DIO 7 to the positive power 
        supply **V+** using the pinout diagram attached in resources.
     7. Set DIO 0 to logic 0 and open the :ref:`Voltmeter<voltmeter>` instrument.
        Start the instrument and monitor the voltage value on Channel 1.
 
         - **Expected Result**: The voltage displayed on the voltmeter is between -0.050V and 0.4V.
+        - **Actual Result**:
+
+..
+  Actual test result goes here.
+..
+        
     8. Set DIO 0 to logic 1 and monitor the voltage value on Channel 1. Start the instrument.
         - **Expected Result**: The voltage displayed on the voltmeter is between 2.9V and 3.4V.
+        - **Actual Result**:
+
+..
+  Actual test result goes here.
+..
+
     9. Open the :ref:`Power Supply instrument<power_supply>` and set the positive 
        power supply to a voltage level between 0V and 0.8V.
        Monitor the DIO 7 logic state.
 
         - **Expected Result**: DIO 7 indicates logic 0 level.
+        - **Actual Result**:
+
+..
+  Actual test result goes here.
+..
+
     10. Open the :ref:`Power Supply instrument<power_supply>` and set the positive
         power supply to a voltage level between 2V and 3.3V.
         Monitor the DIO 7 logic state.
 
          - **Expected Result**: DIO 7 indicates logic 1 level.
+         - **Actual Result**:
+
+..
+  Actual test result goes here.
+..
+
     11. Repeat steps 6 to 11 using DIO 8 as **output** (for step 3) and
         DIO 1 as **input** for (step 4).
 
          - **Expected Result**: All the expected results in step 6 to 11 are met.
+         - **Actual Result**:
+
+..
+  Actual test result goes here.
+..
+
+**Tested OS:**
+
+..
+  Details about the tested OS goes here.
+
+**Comments:**
+
+..
+  Any comments about the test goes here.
+
+**Result:** PASS/FAIL
+
+..
+  The result of the test goes here (PASS/FAIL).
 
-**Result**: PASS/FAIL
 
 Test 2 - Checking grouped digital pin states
 ----------------------------------------------------
@@ -101,12 +168,48 @@ are working correctly.
     3. Set DIO 0-7 as **output** and DIO 8-15 as **input**.
     4. Set DIO 0-7 to value 0.
         - **Expected Result**: DIO 8-15 value indicates the same value as DIO 0-7 group.
+        - **Actual Result**:
+
+..
+  Actual test result goes here.
+..
+
     5. Set DIO 0-7 to value 128.
         - **Expected Result**: DIO 8-15 value indicates the same value as DIO 0-7 group.
+        - **Actual Result**:
+
+..
+  Actual test result goes here.
+..
+
     6. Set DIO 0-7 as **input** and DIO 8-15 as **output**.
     7. Set DIO 8-15 to value 0.
         - **Expected Result**: DIO 0-7 value indicates the same value as DIO 8-15 group.
+        - **Actual Result**:
+
+..
+  Actual test result goes here.
+..
+
     8. Set DIO 8-15 to value 128.
         - **Expected Result**: DIO 0-7 value indicates the same value as DIO 8-15 group.
+        - **Actual Result**:
+
+..
+  Actual test result goes here.
+..
+
+**Tested OS:**
+
+..
+  Details about the tested OS goes here.
+
+**Comments:**
+
+..
+  Any comments about the test goes here.
+
+**Result:** PASS/FAIL
 
-**Result**: PASS/FAIL
+..
+  The result of the test goes here (PASS/FAIL).