A little project into getting a bare 32 pin, TQFP SAMC21E18A chip to do something.
Install the ARM embedded toolkit and openocd (brew install homebrew/cask/gcc-arm-embedded openocd).
Get an Atmel-ICE programmer.
With a pot connected to the chip's ADC and the ADC driving the PWM duty cycle of an LED, we should be able to very accurately adjust the brightness of the LED from off to full brightness.
Connect the programmer to the breadboard
Power up the board.
Figure out the serial number of the ICE programmer. On OSX look in "System Information -> USB"; on Linux use lsusb:
$ lsusb | grep Atmel
Bus 001 Device 004: ID 03eb:2141 Atmel Corp. ICE debugger
$ lsusb -v -s 001:004 | grep iSerial
iSerial 3 J42700008952
Write the serial number to openocd.cfg.
Compile:
$ cd gcc
gcc$ make
Building file: ../hal/src/hal_io.c
ARM/GNU C Compiler
"arm-none-eabi-gcc" -x c -mthumb -DDEBUG -Os -ffunction-sections -mlong-calls -g3 -Wall -c -std=gnu99 \
-D__SAMC21E18A__ -mcpu=cortex-m0plus \
-I"../" -I"../config" -I"../examples" -I"../hal/include" -I"../hal/utils/include" -I"../hpl/adc" -I"../hpl/core" -I"../hpl/divas" -I"../hpl/dmac" -I"../hpl/gclk" -I"../hpl/mclk" -I"../hpl/osc32kctrl" -I"../hpl/oscctrl" -I"../hpl/pm" -I"../hpl/port" -I"../hpl/rtc" -I"../hpl/systick" -I"../hpl/tc" -I"../hpl/tsens" -I"../hri" -I"../" -I"../CMSIS/Core/Include" -I"../samc21/include" \
-MD -MP -MF "hal/src/hal_io.d" -MT"hal/src/hal_io.d" -MT"hal/src/hal_io.o" -o "hal/src/hal_io.o" "../hal/src/hal_io.c"
Finished building: ../hal/src/hal_io.c
...
Finished building target: blinker.elf
"arm-none-eabi-objcopy" -O binary "blinker.elf" "blinker.bin"
"arm-none-eabi-objcopy" -O ihex -R .eeprom -R .fuse -R .lock -R .signature \
"blinker.elf" "blinker.hex"
"arm-none-eabi-objcopy" -j .eeprom --set-section-flags=.eeprom=alloc,load --change-section-lma \
.eeprom=0 --no-change-warnings -O binary "blinker.elf" \
"blinker.eep" || exit 0
"arm-none-eabi-objdump" -h -S "blinker.elf" > "blinker.lss"
"arm-none-eabi-size" "blinker.elf"
text data bss dec hex filename
5552 40 8328 13920 3660 blinker.elf
$
and upload to the MCU:
gcc$ make program
Writing flash...
openocd -f ../openocd.cfg -c "program blinker.elf verify reset exit"
Open On-Chip Debugger 0.10.0
Licensed under GNU GPL v2
For bug reports, read
http://openocd.org/doc/doxygen/bugs.html
none separate
adapter speed: 400 kHz
cortex_m reset_config sysresetreq
Info : CMSIS-DAP: SWD Supported
Info : CMSIS-DAP: JTAG Supported
Info : CMSIS-DAP: Interface Initialised (SWD)
Info : CMSIS-DAP: FW Version = 01.00.0021
Info : SWCLK/TCK = 1 SWDIO/TMS = 1 TDI = 1 TDO = 1 nTRST = 0 nRESET = 1
Info : CMSIS-DAP: Interface ready
Info : clock speed 400 kHz
Info : SWD DPIDR 0x0bc11477
Info : at91samc21n18.cpu: hardware has 4 breakpoints, 2 watchpoints
target halted due to debug-request, current mode: Thread
xPSR: 0x41000000 pc: 0x0000015c msp: 0x200020b0
** Programming Started **
auto erase enabled
Info : SAMD MCU: SAMC21E18A (256KB Flash, 32KB RAM)
wrote 16384 bytes from file blinker.elf in 2.059944s (7.767 KiB/s)
** Programming Finished **
** Verify Started **
verified 5592 bytes in 0.223037s (24.484 KiB/s)
** Verified OK **
** Resetting Target **
shutdown command invoked
$
The LED should now respond to the pot.